БЕСПЛАТНАЯ ДИАГНОСТИКА копировальной техники TOSHIBA

Toshiba e-Studio 2555C Коды ошибок

Code: C020
Description: Developer drive motor abnormality: Thedeveloper drive motor is not rotating normally.

Code: C040
Description: PFP motor abnormality: The PFP motor is not rotating normally. (the case that paper can be fed from any drawer except the PFP)

Code: C130
Description: 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 1st drawer)

Code: C140
Description: 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 2nd drawer)

Code: C150
Description: PFP upper drawer tray abnormality: The PFP upper drawer tray-up motor is not rotating or the PFP upper drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP upper drawer)

Code: C160
Description: PFP lower drawer tray abnormality: The PFP lower drawer tray-up motor is not rotating or the PFP lower drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP lower drawer)

Code: C180
Description: LCF tray-up motor abnormality: The LCF tray- up motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF)

Code: C1A0
Description: LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF)

Code: C1B0
Description: LCF transport motor abnormality: The LCF transport motor is not rotating normally (when paper can be fed from any drawer except the LCF).

Code: C260
Description: Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON, or communication error with CCD board.

Code: C270
Description: Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time.

Code: C280
Description: Carriage home position sensor not going ONwithin a specified time

Code: C290
Description: Scanner fuse blowout: 24V power for the scanning system is not supplied at the scanner warming-up after power-ON.

Code: C370
Description: Drum TBU motor abnormality

Code: C380
Description: Auto-toner sensor-K abnormality (upper limit)

Code: C381
Description: Auto-toner sensor-K abnormality (lower limit)

Code: C390
Description: Auto-toner sensor-C abnormality (upper limit)

Code: C391
Description: Auto-toner sensor-C abnormality (lower limit)

Code: C3A0
Description: Auto-toner sensor-M abnormality (upper limit)

Code: C3A1
Description: Auto-toner sensor-M abnormality (lower limit)

Code: C3B0
Description: Auto-toner sensor-Y abnormality (upper limit)

Code: C3B1
Description: Auto-toner sensor-Y abnormality (lower limit)

Code: C3E0
Description: Developer unit replacement (old-new)detection abnormality

Code: C3E1
Description: Drum/cleaner/charger unit replacement (old- new) detection abnormality

Code: C445
Description: IH coil abnormality after abnormality judgment(pre-running end temperature abnormality)

Code: C446
Description: IH coil abnormality after abnormality judgment(pre-running end temperature abnormality)

Code: C447
Description: IH coil abnormality after abnormality judgment(temperature abnormality at ready status)

Code: C449
Description: IH coil abnormality after abnormality judgment(temperature abnormality at high temperature)

Code: C471
Description: IH board initialization abnormality

Code: C472
Description: Power supply abnormality

Code: C473
Description: Surge pressure detection / power and voltage upper limit abnormality

Code: C474
Description: Power and voltage lower limit abnormality

Code: C475
Description: IH power voltage abnormality (power supply abnormality when door is opened)

Code: C480
Description: IGBT high temperature abnormality

Code: C481
Description: IGBT thermistor breaking abnormality

Code: C4B0
Description: Fuser unit counter abnormality

Code: C4B1
Description: Fuser unit voltage judgment abnormality

Code: C4C0
Description: Fuser unit new/old detection fuse abnormality

Code: C4D0
Description: Fuser thermistor abnormality

Code: C4E0
Description: Fuser pressure roller release abnormality - Though the pressure roller is released, its position cannot be detected.

Code: C4E1
Description: Fuser pressure roller contact/semi-contact abnormality - Though the pressure roller is contacted, its position cannot be detected.

Code: C4E2
Description: Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates.

Code: C550
Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.

Code: C551
Description: RADF model detection error

Code: C560
Description: Communication error between Engine-CPUs

Code: C580
Description: Communication error between LGC board and finisher

Code: C5A0
Description: EEPROM not connected (LGC board)

Code: C5A1
Description: EEPROM data abnormality (LGC board)

Code: C8E0
Description: RADF communication protocol abnormality: The system has to be stopped because the control

Code: C900
Description: Connection error between SYS board andLGC board

Code: C911
Description: Toner cartridge IC chip access board abnormality

Code: C940
Description: Engine-CPU abnormality

Code: C962
Description: LGC board ID abnormality

Code: C964
Description: LGC board boot process abnormality

Code: C970
Description: High-voltage transformer abnormality: Leakage of the main charger is detected.

Code: C9E0
Description: Connection error between scanner CPU and system CPU

Code: CA00
Description: color registration abnormality

Code: CB00
Description: Finisher not connected: Communication error has occurred between the equipment and finisher. [MJ-1107/1108]

Code: CB01
Description: Finisher communication error [MJ-1036] Finisher communication error: Communication error has occurred between the equipment and finisher. [MJ-1107/1108]

Code: CB10
Description: Entrance motor abnormality: The entrance motor is not rotating normally. [MJ-1107/1108]

Code: CB11
Description: Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1107/1108]

Code: CB12
Description: Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1107/1108]

Code: CB13
Description: Finisher exit motor abnormality [MJ-1108]

Code: CB14
Description: Paper holding arm motor abnormality [MJ-1108]

Code: CB30
Description: Movable tray shift motor abnormality: The movable tray shift motor or the movable tray does not work properly. [MJ-1036]Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally. [MJ-1107/1108]

Code: CB31
Description: Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. [MJ-1107/1108]

Code: CB40
Description: Front alignment plate home position detection error: The detection of the home position ends abnormally because the front alignment plate has not worked properly.[MJ-1036]Front alignment motor abnormality: The front alignment motor is not rotating or the front alignment plate is not moving normally. [MJ-1107/1108]

Code: CB50
Description: Stapler unit home position detection error: The detection of the home position of the stapler unit ends abnormally. [MJ-1036]Stapler home position error: The stapler home position sensor does not work. [MJ-1107/1108]

Code: CB51
Description: Stapler unit sliding home position detection error: The detection of the home position of the stapler unit sliding ends abnormally. [MJ-1036]Stapler shift home position error: The stapler is not at the home position. [MJ-1107/1108]

Code: CB60
Description: Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally. [MJ-1107/1108]

Code: CB80
Description: Finisher control PC board (FIN) backup RAM error: An error occurs during the writing of data into the EEPROM of the Finisher. [MJ-1036]Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1107/1108]

Code: CB81
Description: Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. [MJ-1107/1108]

Code: CB82
Description: Finisher - Main CPU program error [MJ-1107/1108]

Code: CB83
Description: Saddle Stitch Finisher - Main CPU program error [MJ-1108]

Code: CB84
Description: Hole Punch Unit - Main CPU program error[MJ-1107/1108/6104]

Code: CB91
Description: Saddle Stitch Finisher flash ROM abnormality[MJ-1108]

Code: CB92
Description: Saddle Stitch Finisher RAM abnormality [MJ-1108]

Code: CB93
Description: Additional folding motor abnormality [MJ-1108]

Code: CB94
Description: Saddle transport motor abnormality [MJ-1108]

Code: CB95
Description: Stacker motor abnormality [MJ-1108]

Code: CBA0
Description: Front saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1108]

Code: CBB0
Description: Rear saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1108]

Code: CBE0
Description: Saddle Stitch Finisher folding motor (M17) abnormality: The folding motor is not rotating or the folding roller is not moving normally. [MJ-1108]

Code: CC02
Description: Stack exit roller nip home position detection error [MJ-1036]

Code: CC20
Description: Saddle communication error [MJ-1108]

Code: CC30
Description: Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. [MJ-1107/1108]

Code: CC31
Description: Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. [MJ-1107/1108]

Code: CC41
Description: Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ-1107/1108]

Code: CC51
Description: Punch unit sliding motor (M12)abnormality[MJ-1036]Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. [MJ-1107/1108 (when MJ-6104 is installed)]

Code: CC52
Description: Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. [MJ-1107/1108 (when MJ-6104 is installed)]

Code: CC54
Description: Abnormality of paper detection sensors (S24 and S25)[MJ-1036]

Code: CC60
Description: Punch motor abnormality [MJ-1036]

Code: CC61
Description: Punch motor abnormality [MJ-1036]Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. [MJ-1107/1108 (whenMJ-6104 is installed)]

Code: CC71
Description: Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1107/1108 (when MJ-6104 is installed)]

Code: CC72
Description: Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1107/1108 (when MJ-6104 is installed)]

Code: CC80
Description: Front alignment motor (M2) abnormality [MJ-1036]Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally. [MJ-1107/1108]

Code: CC93
Description: Knurled roller shift solenoid abnormality [MJ-1036]

Code: CC94
Description: Fan motor abnormality[MJ-1036]

Code: CCF1
Description: Tray safety switch abnormality -(1) The tray safety switch turned on during tray operation (moving up or down).(2) The tray operated with the tray safety switch turned on.

Code: CDE0
Description: Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally. [MJ-1107/1108]

Code: CE00
Description: Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board[MJ-1107/1108 (when MJ-6104 is installed)]

Code: CE10
Description: Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF.

Code: CE20
Description: Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed.

Code: CE40
Description: Image quality control test pattern abnormality: The test pattern is not formed normally.

Code: CE41
Description: Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally.

Code: CE50
Description: Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range.

Code: CE60
Description: Drum thermistor 2 abnormality: The output value of the drum thermistor 2 is out of a specified range.

Code: CE70
Description: Drum drive switching abnormality: The drum switching detection sensor (S11) is not turned ON after the drum motor was rotated for a specified period of time.

Code: CE80
Description: LED head communication error

Code: CE81
Description: Interface initialization error between LED head and LGC board

Code: CE90
Description: Drum thermistor 1 abnormality: The output value of the drum thermistor 1 is out of a specified range.

Code: CF10
Description: Communication module writing failure. [MJ-1107/1108]

Code: F070
Description: Communication error between System-CPUand Engine-CPU

Code: F071
Description: Communication initialization error betweenSystem-CPU and Engine-CPU

Code: F090
Description: SRAM abnormality on the SYS board

Code: F100_0
Description: HDD format error: Operation of HDD key data fails.

Code: F100_1
Description: HDD format error: Encryption key data of either the SYS board or the SRAM board for the SYS board are damaged.

Code: F100_2
Description: HDD format error: Encryption key data of both the SYS board and the SRAM board for the SYS board are damaged.

Code: F101_0
Description: HDD connection error (HDD connection cannot be detected.)

Code: F101_1
Description: Root partition mount error (HDD formatting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the program is mainly stored.

Code: F101_2
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_1 and F101_4 to F101_9 errors.

Code: F101_3
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_1 and F101_4 to F101_9 errors.

Code: F101_4
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/work" partition.

Code: F101_5
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/registration" partition.

Code: F101_6
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/backup" partition.

Code: F101_7
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/imagedata" partition.

Code: F101_8
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/storage" partition.

Code: F101_9
Description: Partition mount error: The HDD cannot be connected (mounted) caused by damage to the "/encryption" partition.

Code: F102
Description: HDD start error: HDD cannot become ‘Ready’state.

Code: F103
Description: HDD transfer time-out: Reading/writing cannot be performed in the specified period of time.

Code: F104
Description: HDD data error: Abnormality is detected in the data of HDD.

Code: F105
Description: HDD other error

Code: F106_0
Description: ADI-HDD error: Illegal disk replacement detected (ADI-HDD Exchange to SATA-HDD)

Code: F106_1
Description: ADI-HDD error: HDD type detection error

Code: F106_10
Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.

Code: F106_2
Description: ADI-HDD error: ADI encryption key download operation error

Code: F106_3
Description: ADI-HDD error: ADI authentication AdminPassword generation error

Code: F106_4
Description: ADI-HDD error: Authentication random number generation error

Code: F106_5
Description: ADI-HDD error: Authentication data transmission error

Code: F106_6
Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.

Code: F106_7
Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.

Code: F106_8
Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.

Code: F106_UND EF
Description: ADI-HDD error: Error caused by reason other than F106_0 to 5 errors.

Code: F109_0
Description: Key consistency error: Consistency check operation error.

Code: F109_1
Description: Key consistency error: SRAM encryption AESkey data damage.

Code: F109_2
Description: Key consistency error: Signature Check public key damage.

Code: F109_3
Description: Key consistency error: HDD encryption parameter damage.

Code: F109_4
Description: Key consistency error: license data damage.

Code: F109_5
Description: Key consistency error: Encryption key for ADI- HDD is damaged.

Code: F109_6
Description: Key consistency error: Administrator password error for ADI-HDD authentication.

Code: F110
Description: Communication error between System-CPUand Scanner-CPU

Code: F111
Description: Scanner response abnormality

Code: F120
Description: Database abnormality: Database is not operating normally.

Code: F121
Description: Database abnormality (user information management database)

Code: F122
Description: Database abnormality (Message/Job log management database)

Code: F124
Description: Database abnormality: Database is not operating normally. (Language management database)

Code: F130
Description: Invalid MAC address

Code: F131
Description: Error due to damage to filtering setting file

Code: F140
Description: ASIC format error: ASIC formatting fails or memory acquiring fails when software is formatted

Code: F200
Description: Data Overwrite option (GP-1070) disabled

Code: F350
Description: SYS board abnormality

Code: F400
Description: SYS cooling fan abnormality

Code: F500
Description: HD partition damage

Code: F510
Description: Application start error

Code: F520
Description: Operating system start error

Code: F521
Description: Integrity check error

Code: F550
Description: Encryption partition error

Code: F600
Description: Software update error

Code: F700
Description: Overwrite error

Code: F800
Description: Date error

Code: F900
Description: Machine information alignment error

Code: F902_1
Description: System firmware / System software model information error - Invalid system firmware/ software is installed.

Code: F902_4
Description: SYS board model information error