БЕСПЛАТНАЯ ДИАГНОСТИКА копировальной техники TOSHIBA

Toshiba e-Studio 2551c Коды ошибок

Code: C010
Description: Main motor abnormality: The main motor is not rotating normally.

Code: C020
Description: Developer drive motor abnormality: The developer drive motor is not rotating normally.

Code: C030
Description: Transport motor abnormality: The transport motor is not rotating normally.

Code: C040
Description: PFP motor abnormality: The PFP motor is not rotating normally. (the case that paper can be fed from any drawer except the PFP)

Code: C130
Description: 1st drawer tray abnormality: The tray-up motor is not rotating or the 1st drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 1st drawer)

Code: C140
Description: 2nd drawer tray abnormality: The tray-up motor is not rotating or the 2nd drawer tray is not moving normally. (the case that paper can be fed from any drawer except the 2nd drawer)

Code: C150
Description: PFP upper drawer tray abnormality: The PFP upper drawer tray-up motor is not rotating or the PFP upper drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP upper drawer)

Code: C160
Description: PFP lower drawer tray abnormality: The PFP lower drawer tray-up motor is not rotating or the PFP lower drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP lower drawer)

Code: C180
Description: LCF tray-up motor abnormality: The LCF trayup motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF)

Code: C1A0
Description: LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF)

Code: C1B0
Description: LCF transport motor abnormality: The LCF transport motor is not rotating normally (when paper can be fed from any drawer except the LCF).

Code: C260
Description: Peak detection error: Lighting of the exposure lamp (white reference) is not detected when power is turned ON.

Code: C270
Description: (1) Carriage home position sensor not turning OFF within a specified period of time: The carriage does not shift from its home position in a specified time.
(2) Downloading firmware with an incorrect model. If the error occurs, the exposure lamp lights twice at the same time.

Code: C280
Description: Carriage home position sensor not going ON within a specified time

Code: C290
Description: Scanner fuse blowout: 24V power for the scanning system is not supplied at the scanner warming-up after power-ON.

Code: C360
Description: Charger cleaner motor abnormality: Charger cleaner motor is not rotating or wire cleaner is not moving normally

Code: C370
Description: Transfer belt motor abnormality (Drum TBU motor abnormality)

Code: C380
Description: Auto-toner sensor-K abnormality (upper limit)

Code: C381
Description: Auto-toner sensor-K abnormality (lower limit)

Code: C390
Description: Auto-toner sensor-C abnormality (upper limit)

Code: C391
Description: Auto-toner sensor-C abnormality (lower limit)

Code: C3A0
Description: Auto-toner sensor-M abnormality (upper limit)

Code: C3A1
Description: Auto-toner sensor-M abnormality (lower limit)

Code: C3B0
Description: Auto-toner sensor-Y abnormality (upper limit)

Code: C3B1
Description: Auto-toner sensor-Y abnormality (lower limit)

Code: C3E0
Description: Developer unit replacement (old-new) detection abnormality

Code: C3E1
Description: Drum/cleaner/charger unit replacement (oldnew) detection abnormality

Code: C411
Description: Thermistor or heater lamp abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON.

Code: C412
Description: Thermistor/heater lamp abnormality at power- ON: Thermistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a specified period of time after power-ON.

Code: C443
Description: Heater lamp abnormality after abnormality judgment (not reaching to intermediate temperature)

Code: C445
Description: Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)

Code: C446
Description: Heater lamp abnormality after abnormality judgment (pre-running end temperature abnormality)

Code: C447
Description: Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)

Code: C448
Description: Heater lamp continuous lighting abnormality: Heater lamp lights continuously for a certain period of time when the pressure roller temperature during ready status is higher than the specified

Code: C449
Description: Heater lamp abnormality after abnormality judgment (temperature abnormality at high temperature)

Code: C450
Description: Abnormal temperature difference between the center thermopile and the edge thermistor
(Heater lamp abnormality after abnormality judgment)

Code: C451
Description: Abnormal temperature difference between the center thermopile and the edge thermistor
(Heater lamp abnormality after abnormality judgment)

Code: C452
Description: Abnormal thermopile temperature difference
(Heater lamp abnormality after abnormality judgment)

Code: C465
Description: Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)

Code: C466
Description: Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality)

Code: C467
Description: Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status)

Code: C468
Description: Pressure roller thermistor abnormality after entering ready status (overheating)

Code: C471
Description: IH power voltage abnormality or IH initial abnormality (IH board initial abnormality)

Code: C472
Description: IH power voltage abnormality (power supply abnormality)

Code: C475
Description: IH power voltage abnormality (power supply abnormality when door is opened)

Code: C480
Description: Overheating of IGBT: The temperature of the IGBT rises abnormally.

Code: C490
Description: IH control circuit or IH coil abnormality: Abnormality is detected in IH control circuit or IH coil is broken/ shorted.

Code: C4B0
Description: Fuser unit counter abnormality

Code: C4B1
Description: Fuser unit destination selection abnormality

Code: C4C0
Description: Fuser unit new/old detection fuse abnormality

Code: C4D0
Description: Fuser belt thermopile abnormality

Code: C4F0
Description: Center thermistor error correction

Code: C4F1
Description: Side thermistor error correction

Code: C550
Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.

Code: C551
Description: RADF model detection error

Code: C560
Description: Communication error between Engine-CPU and PFC board

Code: C570
Description: Communication error between Engine-CPU and IPC board

Code: C580
Description: Communication error between IPC board and finisher

Code: C5A0
Description: EEPROM not connected (LGC board)

Code: C5A1
Description: EEPROM data abnormality (LGC board)

Code: C8E0
Description: RADF communication protocol abnormality: The system has to be stopped because the control

Code: C900
Description: Connection error between SYS board and LGC board

Code: C901
Description: System format error for scanner

Code: C910
Description: Toner cartridge IC chip access board abnormality

Code: C911
Description: Toner cartridge IC chip access board abnormality (caused by factors other than C910)

Code: C940
Description: Engine-CPU abnormality

Code: C960
Description: Connection error between LGC board and DRV board, ID abnormality

Code: C962
Description: LGC board ID abnormality

Code: C970
Description: High-voltage transformer abnormality: Leakage of the main charger is detected.

Code: C9E0
Description: Connection error between SLG board and SYS board

Code: CA00
Description: color registration abnormality

Code: CA10
Description: Polygonal motor abnormality: The polygonal motor is not rotating normally.

Code: CA20
Description: H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams.

Code: CB00
Description: Finisher not connected: Communication error has occurred between the equipment and finisher.

Code: CB01
Description: Finisher communication error: Communication error has occurred between the equipment and finisher.

Code: CB10
Description: Entrance motor abnormality: The entrance motor is not rotating normally.

Code: CB11
Description: Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally.

Code: CB12
Description: Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally.

Code: CB13
Description: Finisher exit motor abnormality

Code: CB14
Description: Paper holding arm motor abnormality

Code: CB20
Description: Delivery motor abnormality: Delivery motor or delivery roller is not rotating normally.

Code: CB30
Description: Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally.

Code: CB31
Description: Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly.

Code: CB40
Description: Front alignment motor abnormality: The front alignment motor is not rotating or the front align/1106ment plate is not moving normally.

Code: CB50
Description: Staple unit abnormality: Staple unit is not moving normally. Stapler home position error: The stapler home position sensor does not work.

Code: CB51
Description: Stapler shift home position error: The stapler is not at the home position.

Code: CB60
Description: Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally.

Code: CB70
Description: Paper loading amount detection sensor abnormality

Code: CB80
Description: Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON.

Code: CB81
Description: Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON.

Code: CB82
Description: Finisher - Main CPU program error

Code: CB83
Description: Saddle Stitch Finisher - Main CPU program error

Code: CB84
Description: Hole Punch Unit - Main CPU program error

Code: CB90
Description: Paper folding blade motor (M12) abnormality

Code: CB91
Description: Saddle Stitch Finisher flash ROM abnormality

Code: CB92
Description: Saddle Stitch Finisher RAM abnormality

Code: CB93
Description: Additional folding motor abnormality

Code: CB94
Description: Saddle transport motor abnormality

Code: CB95
Description: Stacker motor abnormality

Code: CBA0
Description: Front saddle stapler home position error: The stapler home position detection is abnormally operated and finished.

Code: CBB0
Description: Rear saddle stapler home position error: The stapler home position detection is abnormally operated and finished.

Code: CBC0
Description: Saddle Stitch Finisher side alignment motor (M15) abnormality: The alignment motor is not rotating or the alignment plate is not working properly.

Code: CBD0
Description: Guide motor abnormality: Guide motor is not rotating or guide is not moving normally

Code: CBE0
Description: Saddle Stitch Finisher folding motor (M17) abnormality: The folding motor is not rotating or the folding roller is not moving normally.

Code: CBF0
Description: Stacker motor (M9) abnormality

Code: CC00
Description: Sensor connector abnormality: Connector of guide home position sensor, paper pushing plate home position sensor or paper pushing plate top position sensor is disconnected.

Code: CC02
Description: Stack exit roller nip home position detection error[MJ-1036] Exit roller nip adjustment motor (M4) abnormality[MJ-1037]

Code: CC10
Description: Micro switch abnormality: With all covers closed, inlet door switch, delivery door switch or front cover switch is open.

Code: CC20
Description: Saddle communication error

Code: CC21
Description: Saddle stitch 3rd transport roller drive motor (M10) abnormality[MJ-1037]

Code: CC22
Description: Saddle stich stapler home position detection error[MJ-1037]

Code: CC23
Description: An abnormal interruption of the encoder pulse of the folding blade occurrs.

Code: CC30
Description: Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. Stack delivery motor abnormality: The stack delivery motor is not rotating normally.

Code: CC31
Description: Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally.

Code: CC40
Description: Swing motor abnormality: Swing motor is not rotating or swing unit is not moving normally

Code: CC41
Description: Paper holder cam home position abnormality: The paper holder cam is not at the home position.

Code: CC50
Description: Horizontal registration motor abnormality: Horizontal registration motor is not rotating or puncher is not shifting normally

Code: CC51
Description: Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally.

Code: CC52
Description: Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally.

Code: CC53
Description: Punch waste full sensors (S41 and S42) abnormality[MJ-1037]

Code: CC54
Description: Abnormality of paper detection sensors (S24 and S25)[MJ-1036] Abnormality of trailing edge detection sensors (S39 and S40) and horizontal registration detection sensors (S39 and S40)[MJ-1037]

Code: CC60
Description: Punch motor abnormality [MJ-1036] Punch motor (M15) abnormality [MJ-1037]

Code: CC61
Description: Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally.

Code: CC71
Description: Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on.

Code: CC72
Description: Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on.

Code: CC80
Description: Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally.

Code: CC90
Description: Tray shift motor abnormality: The tray shift motor is not rotating or the stack tray is not moving normally.

Code: CC91
Description: The detection of the home position of the gripper arm ends abnormality.

Code: CC92
Description: Movable tray upper limit detection error [MJ- 1037]

Code: CC93
Description: Knurled roller shift solenoid abnormality [MJ- 1036]

Code: CC94
Description: Fan motor abnormality[MJ-1036]

Code: CCB0
Description: Offset motor abnormality: The offset motor is not rotating normally.

Code: CCD0
Description: Stack ejection motor abnormality: Stack ejection motor or stack ejection roller is not rotating normally

Code: CCE0
Description: Paper trailing edge assist motor abnormality: Paper trailing edge assist motor is not rotating or paper trailing edge assist is not moving normally

Code: CCF0
Description: Gear changing motor abnormality: Gear changing motor is not rotating normally

Code: CCF1
Description: Tray safety switch abnormality -
(1) The tray safety switch turned on during tray operation (moving up or down).
(2) The tray operated with the tray safety switch turned on.

Code: CD70
Description: Waste toner box mixing paddle locked: The mixing paddle in the waste toner box does not rotate.

Code: CD71
Description: Waste toner motor locking error ("Waste toner box replacement"): "Waste toner box replacement" appears when either CD70 or CD71 error occurs. The error code CD72 is noted on the error history and logs.

Code: CDE0
Description: Paddle motor abnormality: The paddle motor is not rotating or the paddle is not rotating normally.

Code: CE00
Description: Communication error between finisher and punch unit: Communication error between finisher controller PC board and punch controller PC board

Code: CE00
Description: Communication error (signal transmission to the Hole Punch Unit) [MJ-1037]

Code: CE10
Description: Image quality sensor abnormality (OFF level): The output value of this sensor is out of a specified range when sensor light source is OFF

Code: CE20
Description: Image quality sensor abnormality (no pattern level): The output value of this sensor is out of a specified range when the image quality control test pattern is not formed.

Code: CE40
Description: Image quality control test pattern abnormality: The test pattern is not formed normally

Code: CE41
Description: Image quality TRC control test pattern abnormality: The image quality TRC control test pattern is not printed normally.

Code: CE50
Description: Temperature/humidity sensor abnormality: The output value of this sensor is out of a specified range.

Code: CE60
Description: Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range

Code: CE70
Description: Drum drive switching abnormality: The drum switching detection sensor (S19) is not turned ON after the drum motor was rotated for a specified period of time.

Code: CE71
Description: Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor (S43) and K drum phase sensor (S44)) are not turned ON after the drum motor was rotated for a specified period of time.

Code: CE80
Description: LED head communication error

Code: CE81
Description: Interface initialization error between LED head and LGC board

Code: CE90
Description: Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range.

Code: CEC0
Description: 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally.

Code: CEC1
Description: 2nd transfer roller contacting position detection abnormality

Code: CEC2
Description: 2nd transfer roller releasing position detection abnormality

Code: CF10
Description: Communication module SRAM reading failure.

Code: CF90
Description: Laser optical unit shutter abnormality.

Code: CF91
Description: NVRAM abnormality on the SYS board

Code: CF92
Description: SRAM and NVRAM abnormality on the SYS board

Code: E010
Description: Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor.

Code: E011
Description: Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor.

Code: E013
Description: The paper jam occurred between the registration pass sensor and the paper clinging detection sensor.

Code: E020
Description: Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor.

Code: E030
Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.

Code: E061
Description: Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment.

Code: E062
Description: Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.

Code: E063
Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.

Code: E064
Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.

Code: E065
Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.

Code: E090
Description: Image data delay jam: Image data to be printed cannot be prepared

Code: E091
Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.

Code: E0A0
Description: Image transport ready time-out jam: Image data to be printed cannot be sent.

Code: E110
Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.

Code: E120
Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.

Code: E130
Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.

Code: E140
Description: 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor.

Code: E150
Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.

Code: E160
Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor.

Code: E190
Description: LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.

Code: E200
Description: 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.

Code: E210
Description: 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.

Code: E220
Description: 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.

Code: E270
Description: Bypass transport jam (Paper not reaching the registration sensor): Paper fed from the bypass tray and passed through the bypass feed sensor does not reach the registration sensor.

Code: E300
Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.

Code: E310
Description: PFP upper drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.

Code: E320
Description: PFP upper drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor.

Code: E330
Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.

Code: E340
Description: PFP lower drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.

Code: E350
Description: PFP lower drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor.

Code: E360
Description: PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor.

Code: E3C0
Description: LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor.

Code: E3D0
Description: LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor.

Code: E3E0
Description: LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor.

Code: E400
Description: Jam access cover open jam: The jam access cover has opened during printing.

Code: E410
Description: Front cover open jam: The front cover has opened during printing.

Code: E420
Description: PFP side cover open jam: The PFP side cover has opened during printing.

Code: E430
Description: ADU open jam: The ADU has opened during printing.

Code: E440
Description: Side cover open jam: The side cover has opened during printing.

Code: E450
Description: LCF side cover open jam: The LCF side cover has opened during printing.

Code: E480
Description: Bridge unit open jam: The bridge unit has opened during printing.

Code: E4A0
Description: Waste toner cover open jam: The waste toner cover has opened during printing.

Code: E510
Description: Jam not reaching the ADU entrance sensor: The paper does not reach the ADU entrance sensor after it is switchbacked in the exit section.

Code: E520
Description: Stop jam in the ADU: The paper does not reach the ADU exit sensor after it has passed the ADU entrance sensor.

Code: E550
Description: Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished.

Code: E551
Description: Paper remaining jam on the transport path (when a service call occurs)

Code: E552
Description: Paper remaining jam on the transport path (when the cover is closed)

Code: E712
Description: Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor

Code: E714
Description: Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.

Code: E721
Description: Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).

Code: E722
Description: Jam not reaching the original exit/reverse sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section.

Code: E724
Description: Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor.

Code: E725
Description: Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.

Code: E726
Description: Transport/exit signal reception jam: RADF receives the transport/exit reception signal from the equipment when no original is at the exposure waiting position

Code: E731
Description: Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor.

Code: E860
Description: RADF jam access cover open: The RADF jam access cover has opened during RADF operation.

Code: E870
Description: RADF open jam: RADF has opened during RADF operation

Code: E871
Description: Cover open jam in the read ready status

Code: E910
Description: Jam at the bridge unit transport sensor 1: The paper does not reach the bridge unit transport sensor 1 after it has passed the exit sensor.

Code: E920
Description: Stop jam at the bridge unit transport sensor 1: The trailing edge of the paper does not pass the bridge unit transport sensor 1 after its leading edge has reached the sensor.

Code: E930
Description: Jam at the bridge unit transport sensor 2: The trailing edge of the paper does not reach the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 1.

Code: E940
Description: Stop jam at the bridge unit transport sensor 2: The trailing edge of the paper does not pass the bridge unit transport sensor 2 after its leading edge has reached the bridge unit transport sensor 2.

Code: E9F0
Description: Punching jam: Punching is not performed properly. [MJ-1101/1106 (when MJ-6103 is installed)]

Code: EA10
Description: Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor.[MJ-1031/1101] The paper which has passed the bridge unit does not reach the inlet sensor. [MJ-1106]

Code: EA20
Description: Paper transport stop jam: The paper does not pass through the inlet sensor. The paper which has passed through the inlet sensor does not reach the feeding sensor. [MJ- 1101/1106]

Code: EA21
Description: Paper size error jam: Paper does not reach the sensor because the paper is shorter than spec. [MJ-1101/1106]

Code: EA22
Description: Paper transport jam (Finisher paper punching edge detection sensor): The paper position sensor on the Finisher transport path detects paper shorter than the acceptable paper size. [MJ-1101/1106]

Code: EA23
Description: Paper transport jam (transport sensor): Paper being transported on the Finisher transport path is stopped at the outlet sensor at 27.56 inches or longer. [MJ-1101/1106]

Code: EA24
Description: Paper transport jam (between entrance and transport sensors): The leading edge of paper which has passed the entrance sensor on the Finisher transport path does not reach the transport sensor. [MJ-1101/1106

Code: EA25
Description: Paper transport jam (after paper stack exit): The finishing tray paper detection sensor detects paper after a stack of paper exits from the finishing tray. [MJ-1101/1106]

Code: EA26
Description: Paper transport jam (stop command request): A command to stop equipment operation is received while paper is being transported in the Finisher. [MJ-1101/1106]

Code: EA27
Description: Paper transport jam (paper not inserted): The equipment detects a paper-not-inserted jam but the entrance sensor is turned ON before the equipment is stopped. [MJ-1101/1106]

Code: EA28
Description: Paper transport jam (paper holder plate operation delay): An attempt to start the arm assisting operation for dropping paper on the finishing tray is made, but the previous arm assisting operation has not yet been finished. [MJ-1101/1106]

Code: EA29
Description: Paper transport jam (stack transport delay): The buffer tray is extended to drop a stack of paper on the finishing tray but the previous stack has not yet exited. [MJ-1101/1106]

Code: EA30
Description: Power-ON jam: Paper exists at the inlet sensor when power is turned ON. [MJ-1031]

Code: EA31
Description: Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ-1101/ 1106]

Code: EA32
Description: Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON. [MJ-1101/1106]

Code: EA40
Description: Joint open jam: The finisher cover opened during machine operation. [MJ-1031] Cover open error: The front cover or stationary tray is opened during paper transport. [MJ-1106]

Code: EA50
Description: Stapling jam: Stapling is not performed properly. [MJ-1031/1101]

Code: EA60
Description: Early arrival jam: The inlet sensor detects the paper earlier than a specified timing. [MJ-1031/1101/1106]

Code: EA70
Description: Stack exit belt home position error: The stack exit belt is not at the home position. [MJ-1101/ 1106] Stack slider home position error: The stack slider is not at the home position. [MJ-1031]

Code: EA90
Description: Door open jam: The delivery cover or inlet cover has opened during printing. [MJ-1106]

Code: EAA0
Description: Paper remaining in Saddle Stitch Finisher: Paper remaining in Saddle Stitch Finisher [MJ- 1106]

Code: EAB0
Description: Paper transport jam in Saddle Stitch Finisher: Paper transport jam in Saddle Stitch Finisher [MJ-1106]

Code: EAB1
Description: Short paper jam: Short paper jam (Saddle Stitch Finisher) [MJ-1106]

Code: EAD0
Description: Print end command time-out jam: The printing has not finished normally because of an error occurring on the interface between the SYS board and the engine firmware at the end of printing.

Code: EAE0
Description: Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher.

Code: EB30
Description: Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing.

Code: EB50
Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper.

Code: EB60
Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]).

Code: ED10
Description: Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1101/ 1106 (when MJ-6103 is installed)]

Code: ED11
Description: Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1101/1106 (when MJ-6103 is installed)]

Code: ED12
Description: Shutter home position error: The shutter is not at the home position. [MJ-1101/1106]

Code: ED13
Description: Front alignment plate home position error: The front alignment plate is not at the home position. [MJ-1101/1106]

Code: ED14
Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ-1101/1106]

Code: ED15
Description: Paddle home position error: The paddle is not at the home position. [MJ-1101/1106]

Code: ED16
Description: Buffer tray home position error: The buffer tray is not at the home position. [MJ-1101/1106]

Code: EF10
Description: Paper not supported for Saddle Stitch Finisher: Unsupported paper size, type and an excess number of pages for stapling are selected. [MJ- 1106]

Code: EF11
Description: Saddle Stitch Finisher stapling error (front): Front stapling is not correctly done. [MJ-1106]

Code: EF12
Description: Saddle Stitch Finisher stapling error (rear): Rear stapling is not correctly done. [MJ-1106]

Code: EF13
Description: Saddle paper holder home position detection abnormality: The paper holder home position cannot be detected. [MJ-1106]

Code: EF14
Description: Saddle paper exit jam: Outputting paper is not completed within a fixed time. [MJ-1106]

Code: EF15
Description: Saddle Stitch Finisher side alignment motor home position detection abnormality: The side alignment motor home position cannot be detected. [MJ-1106]

Code: EF16
Description: Saddle Stitch Finisher stacker motor home position detection abnormality: The stacker motor home position cannot be detected. [MJ- 1106]

Code: EF17
Description: Saddle Stitch Finisher folding blade home position detection abnormality: The folding blade home position cannot be detected. [MJ- 1106]

Code: EF18
Description: Saddle Stitch Finisher additional folding roller home position detection abnormality: The additional folding roller home position cannot be detected. [MJ-1106]

Code: EF19
Description: Saddle paper folding jam: Fold processed paper cannot be transported to the additional folding roller. [MJ-1106]

Code: EF20
Description: Saddle stacker jam: Transported paper cannot be detected in the stacker.

Code: F070
Description: Communication error between System-CPU and Engine-CPU

Code: F071
Description: Communication initialization error between System-CPU and Engine-CPU

Code: F090
Description: SRAM abnormality on the SYS board

Code: F100
Description: HDD format error: HDD cannot be initialized normally

Code: F100_0
Description: HDD format error: Operation of HDD key data fails.

Code: F100_1
Description: HDD format error: Encryption key data of either the SYS board or the SRAM board for the SYS board are damaged.

Code: F100_2
Description: HDD format error: Encryption key data of both the SYS board and the SRAM board for the SYS board are damaged.

Code: F101
Description: HDD unmounted: Connection of HDD cannot be detected

Code: F101_0
Description: HDD connection error (HDD connection cannot be detected.)

Code: F101_1
Description: Root partition mount error (HDD formatting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the program is mainly stored.

Code: F101_2
Description: Normal partition mount error (HDD normal partition mounting fails.): The HDD cannot be connected (mounted) caused by damage to areas other than those described in the F101_0 and F101_1 errors.

Code: F101_3
Description: Encryption partition mount error (HDD encryption partition mounting fails.): The HDD cannot be connected (mounted) caused by damage to the areas in which the key is stored.

Code: F102
Description: HDD start error: HDD cannot become ‘Ready’ state.

Code: F103
Description: HDD transfer time-out: Reading/writing cannot be performed in the specified period of time.

Code: F104
Description: HDD data error: Abnormality is detected in the data of HDD.

Code: F105
Description: HDD other error

Code: F106
Description: Point and Print partition damage

Code: F106_0
Description: ADI-HDD error: Illegal disk replacement detected (ADI-HDD Exchange to SATA-HDD)

Code: F106_1
Description: ADI-HDD error: HDD type detection error

Code: F106_2
Description: ADI-HDD error: ADI encryption key download operation error

Code: F106_3
Description: ADI-HDD error: ADI authentication Admin Password generation error

Code: F106_4
Description: ADI-HDD error: Authentication random number generation error

Code: F106_5
Description: ADI-HDD error: Authentication data transmission error

Code: F108
Description: SHA partition damage

Code: F109_0
Description: Key consistency error: Consistency check operation error.

Code: F109_1
Description: Key consistency error: SRAM encryption AES key data damage

Code: F109_2
Description: Key consistency error: Signature Check public key damage.

Code: F109_3
Description: Key consistency error: HDD encryption parameter damage.

Code: F109_4
Description: Key consistency error: license data damage.

Code: F109_5
Description: Key consistency error: Encryption key for ADIHDD is damaged.

Code: F109_6
Description: Key consistency error: Administrator
password error for ADI-HDD authentication.

Code: F110
Description: Communication error between System-CPU and Scanner-CPU

Code: F111
Description: Scanner response abnormality

Code: F120
Description: Database abnormality: Database is not operating normally.

Code: F121
Description: Database abnormality (user information management database)

Code: F122
Description: Database abnormality (Message/Job log management database)

Code: F124
Description: Database abnormality: Database is not operating normally. (Language management database)

Code: F130
Description: Invalid MAC address

Code: F131
Description: Error due to damage to filtering setting file

Code: F140
Description: ASIC format error: ASIC formatting fails or memory acquiring fails when software is formatted

Code: F200
Description: Data Overwrite option (GP-1070) disabled

Code: F350
Description: SLG board abnormality

Code: F400
Description: SYS board cooling fan abnormality

Code: F500
Description: HD partition damage

Code: F510
Description: Application start error

Code: F520
Description: Operating system start error

Code: F521
Description: Integrity check error

Code: F550
Description: Encryption partition error

Code: F600
Description: Software update error

Code: F700
Description: Overwrite error

Code: F800
Description: Date error

Code: F900
Description: Machine information alignment error

Code: F902_0
Description: Mistaken HDD installation error

Code: F902_1
Description: System firmware / System software model information error - Invalid system firmware/ software is installed on 20/25 ppm model.

Code: F902_3
Description: System firmware / System software model information error - Invalid system firmware/ software is installed on LL20/LL25 ppm model.